led pixel 12mm ws2811

led pixel 12mm ws2811

Model : LED lights all series / exposed waterproof string lights Full / Pixel Light

Category : LED luminous characters

Display color : full color

Display : Static

Pixel diameter : 12 mm

Brightness : Highlight

Grayscale : 256 Level

Product Name: Full lantern string / LED luminous characters / LED exposed light string lights / LED full-color light-emitting character string lights square

Punching size: 12mm

Lamp size: 8mm 

Input voltage: DC5V

Working Current: 20MA 

Rated power: 0.3W

Viewing angle: 120-180

PVC waterproof grade: IP68 

Package: 50 a bunch, anti-static bag packaging, carton packaging.

 

All lights string LED Chong Kong Faguang word called led perforation word / led outside the luminous characters / led Exposed punch word / led the exposed light word / led exposed perforation word / Full lantern string , etc., it is made ​​of metal paint box and LED light source composition, nighttime colorful and very penetrating, giving a full, powerful, progressive feel, very expressive and very good visual impact.

Full lantern string This product is a dot light source punching board practices, special bayonet design, drilling directly after installation, with easy installation, high brightness, safety and energy saving, long life, low attenuation, and other characteristics, quick installation time, convenient maintenance. For high-rise buildings billboards, exposed light word, printing, plastic characters, a variety of lighting inside and outside light source. Select lamp according to floor level spacing, lamp and lamp center distance of 3 cm-6cm most suitable

 

First,  the whole exposed waterproof string lights Features: 

1 ,  the exposed waterproof string lights all give full play to LED spot light advantages, any combination, so that LED luminous characters outside, a large outdoor LED advertising signs, LED electronic light box made ​​easier. 

2 , special bayonet design, drilling directly after installation, quick installation time, quick and easy maintenance. 

3 , a variety of perforated plates can be used (such as electrolytic plate, aluminum plate, iron, stainless steel, etc.). 

4 , Taiwan brand LED chip, strong brightness, light color consistency, good color saturation, long life, low attenuation, energy saving features, to ensure product quality. 

5 , using the parallel connection, breaking the traditional " one does not light, all lights neither bright " shortcomings. 

6 , the whole string of lights , the use of intelligent control system can produce gradient, jump, chase , scan , display graphics and other animation effects, and asynchronous and synchronous control, random order, to meet different user requirements.

 

Second, the full-color  light string specifications: 

1 , the working voltage: DC5V ; 

2 , Color: full color.

 

Third, all lights string / exposed waterproof string lights Full / Pixel Light use: 

  with LED exposed light string do outdoor light word, outdoor signs but also highlight the brand and fashion, greatly enhance the business size and grade. Mainly used for: building roof in large letters, the hotel outdoor signs, KTV and other entertainment signs, store signs, door signs and the like.

 

Fourth, the use Notes: 

1 , light string  voltage of DC5V, note the use of that type of voltage. 

2 , the wire leads from the power supply cross-sectional area not less than 4 mm2 (also possible 2 Article 2.5 in).

4 , Lights of electronic line received power of white negative (some for 2 bars, and after receiving negative). 

5 , if found individual does not light, check the lights or lines, such as not bright, replace LED lamps.

6 , the whole string of lights  in four lines , red for positive, blue is negative, white for the data line DAT

Read More

No comments

LedEdit 2012

The LedEdit Software Instructions
1, Install the software to PC and open
English version:
When we installed The LedEdit Software, on the desktop we can see
following icon:
Please Double-click it, then we into following interface:

In this interface, we can change the language, follows:
 We can Click -Æ “ 语言（ Language ） ”-Æ “ 英 文
（Language）”, the interface will change to this:
The English interface fit to us to use. 2,Make effect Program:
We can click the “File” in the English interface, do as following:
 —>”new project”—> it will appear this interface:
Controller Type: you can select the “Controller Type”. If you use the
SW-CP2000 controller, you must select the “T-1000-6803”; If you use
the SW-CP4000 controller, you must select the “T-4000-6803”; If you
use the SW-CP8000 controller, you must select the “T-8000B-6803”.
Frame Rate: you can select the corresponding number. If you want
to the speed faster, you can select large number; If you want to speed
slower, you can select small number. We recommend you select the
30.
Save as: this appears to you saved address. You can change the
“saved address” by “Browse”. We use the T-1000-6803 controller for Example
We can set as follow:
 Click “OK”, we into follow interface:
Then, we need to set the light layout. We use the 200 light as
the Example.
We click the “ Project Config”—>”start manual layout”—> as follow
interface: In top interface :
 “select”
 Light Horizontal

 Light Vertical
 Line
 Port


 Delete

Because we use 200 lighter, then we click , and the mouse
click ,and do not release the mouse , and dragging to follow:
We can see the Round is horizontal
Then we need to click the , and click The upper left corner, follow: Then we need to click the , and connect the Port with the Round. Follow:
So we made the light layout about 200.
Then we need to save it.
We click the —>”save”—> follow:
You can save where you want to save. It will generate the
document of “.cxb”.
When we saved it, we can close the follow interface: Then we back the interface:
Then we click —>”import(.cxb)”—>follow: We need to find the document that we saved the document of
“.cxb”, and we need to open it.
It will appear the follow interface:
The white point is we needs.
Then we click , it have some program-effection, you can
select one. So we select the “ move right”, it appear follow effection:
Then we must to record the effection, please click the , to start
recording. When we record the effection, we need to click the to
stop recording. The denotes we have recorded 98
Frames.
Then we need to click the , close the “.swf/default Effect”. It back
the interface: Then we can preview the effection that we made, Which we can found
where is wrong or right. Please click the .
We can see the running. If we want to stop it, we can click
.
If you found that had some wrong effcetion, we can delete it,
follow:
We click the —> , and the frame is appear ,
then we drag our mouse ,follow:
And the frame is appear, which means that the frame was selected
from 19 to 29 at the same time we click right of mouse—>”delete”, So
we deleted the wrong effection from 19 to 29 frames. The
 to , because we deleted 10 frames. Then
we click the to follow interface:
Then we click the , it is OK. 3,Export the effect program which we
made.
Please click the —> “export effect(.led)” to follew interface:
We can save the here where you want to save
Then the interface is appear follow:
Click “OK” The all Steps is over , we can close the follow interface:
We can find the document that we needs.
and it need to copy to “SD card”, but the SD card must
to format to “FAT” Format.
4, Other methods.
When we set the layout, we have the other two
methods:
1. Click the —>“auto layout”, follow interface: We only change two parts. the —>
, the —>
, so the interface was changed to this, follow:
Click the “OK”,
The light layout is the same effect, follow: 2. We can use the “Auto CAD” software to set layout.
When we use the “Auto CAD”, we have some request, follow:
The round radius must is 1.0, and the round must be disjoint,
and when we use beeline to connect with two rounds, the
beeline must connect center of a circle. We need make the
“P1” as the port, Follow:
When we save the “Auto CAD” document, we must save it in
“.dxf” format.
Then we can import the “Auto CAD” document of “.dxf” format.
Click the —>”import(.dxf)”—> follows: That effection is the same.
When we import the program-effection, we can
import the “FLASH” that we made. But the “FLASH”
format is the “.swf” format.
 Click the —>”Open(.swf)” —>follow interface:
Select the “FLASH”, that is OK. It will appear follow :
 The follow step is the same as above

Read More

No comments

C1 control led

C1

 C1 System Features     
1,32 level -65 536-level grayscale control, software Gamma correction process.
 2, supports a variety of point, line, surface light source, supports a variety of rules, shaped handle.
 3, single-port controller output, the largest with 2048 pixels.
 4, offline control and play content stored in the SD card.
 5, C1 store up to 16 files, multiple files sequentially copied to SD card.
 6, stored in the SD card's effect should in turn be named: 00_1.led, 01_1.led, 02_1.led.
7, compatible with single-wire IC, then single-IC fixtures, no need CLK clock.

 Note: When 1 C1 ports with load 512 lights, the playback speed of up to 30 frames / sec ports with load more than 512 lights, frame rate with     


  Increasing the number of lights automatically reduced. Second,

support chips	Software support chips Ledctrl	corresponding model	single load lights Remarks
TM1803,TM1804,TM1809,TM1812	C1-TM	2048pixels	There are high-speed and low-speed points
TM1829	C1-TM1829	2048pixels	There are high-speed and low-speed points
UCS1903,UCS1903B ,UCS1909，UCS1912	C1-UCS256	2048pixels	There are high-speed and low-speed points
UCS2903,UCS2909,UCS2912,	C1-UCS256	2048pixels	There are high-speed and low-speed points
UCS6909，UCS6912，UCS7009，UCS5903	C1-UCS32	2048pixels
WS2811	C1-WS2811	2048pixels	There are high-speed and low-speed points
INK1003	C1-TM	2048pixels	There are high-speed and low-speed points
TLS3100	C1-TM	2048pixels	There are high-speed and low-speed points
SM16711	C1-SM16711	2048pixels	There are high-speed and low-speed points
SM16716	C1-SM16716	2048pixels
SM16726	C1-SM16726	2048pixels
LPD6803,D705,1101	C1-6803	2048pixels
LPD8806,LPD8809	C1-8806	2048pixels
P9813	C1-P9813	2048pixels
WS2801,WS2803	C1-WS2801	2048pixels
GW6203	C1-TM	2048pixels

 Third, the appearance of the picture:   Figure a Figure II Four, silk meanings:      
Key meaning: Key implications Save SET to save settings (If you press the SET button, the current settings file and playback speed is saved after the next boot still press play). 
Mode MODE switch file
 Speed ​​SPEED + speed while pressing SPEED + and SPEED-, then enter the file loop playback mode Slow down the speed SPEED-                                        


TTL signal (245 signals): CLK clock line power supply indicator lamp POWER DAT data line failure ERROR LED lights GND Ground SD SD Card Slot Note:


TTL signal output for the controller and lamps must be for the land (that is, the ground and the lamp output is connected to ground controllers together).

 V. wiring   Note: 1, C1 is a single output port, with up to 2048 pixels; 
2, when the control single-controller IC simply DAT and GND GND with lamps DAT and connected to the corresponding. When the control wire to the controller IC to be DAT.CLK and GND and lamps DAT, CLK and GND are connected to the corresponding.
 3, the new project in effect when editing software, select Control Model: C1-IC Model Six, file storage:

 File naming rules:
 The effect of naming a single controller
 "00_1.led" --------- first one results "01_1.led" --------- The first two effects
 "02_1.led" --------- The first three results
 "03_1.led" --------- Section 4 results Seven specific parameters:    

Card:       
  Type: SD Card        
  Capacity: 128MB-2GB         
  Format: FAT format            
Save the document:. * Led    

Physical parameters:
 Working temperature: -30 ℃ -85 ℃           
Power supply: DC 5V input          
 Power consumption: 1W
 Data transfer port: 3pin terminal block
 Weight: 0.25Kg with packaging (3pin terminal block * 1; SD card * 1; Power Adapter * 1; Tray * 1) Size:  

Note: Before you copy files to the SD card, you must format the SD card, attention is to be formatted before each copy. SD card must be formatted as "FAT" format.  

Note: SD card controller can not hot-swappable, plug the SD card each time that you must first disconnect the power controller.
 Eight, FAQs treatment: Question
1: After power, C1 errors found ERROR indicator has been flashing, and no effect output A: The error LED flashes ERROR been proven reader controller is not correct, there may be a problem are:      ①SD card inside is empty, there is no effect file.    
     ②SD card inside the effect file * .led files and controller models do not match, the latest version Ledctrl inside the right choice model C1- controller chip model, and re-create the effect of file * .led.      ③SD card effect until a copy of the file is not formatted as FAT kinds.     
     ④ Replace the SD card before testing, SD card bad possibilities excluded.
     ⑤ effect file name wrong, change 00.led.

 Question 2: After the controller is powered lights normal, but no effect changes in lighting A: The reasons for this are the following:     
① Check the signal lines and lighting controller is not connected properly.     
② lamps and controllers must be common ground that the lamp ground and ground controllers to be tied together.     
③ Please check the effect of making the SD card files * When .led selected models used are consistent with the current lighting chips.

 Question 3: Connect the controller and lighting, strobe lighting, and there is the effect of the change, while the controller LEDs display properly. A:
① ground between the controller and the lighting is not connected.      Effect made ​​
②SD card inside a mistake, do not match the selected effect when the actual lighting fixtures chips and chips.
 ③ insufficient supply voltage lamps.

 Problem 4: SD card can not be formatted. A:
① first confirm whether the side of the SD card protection switch is already unlocked. Unlocking direction SD card lilies that end.
 ② protection lock has been designed according to the requirements, but still can not be formatted, if that happens, most of SD card reader is broken, replace the SD card reading device.
 ③ If the above actions do not solve the problem of formatting, replace the SD card and re-tested.

Read More

1 comment

T-1000

First, the system features

  1 , 32 grade - 65536 level grayscale control, software Gamma correction process.

2 , supports a variety of point, line, surface light source, supports a variety of rules, shaped handle.

3 , the controller outputs a single port, which can carry 1024/2048 lights.

4 , a single line control, play content stored in the SD card.

5 , maximum storage of 16 files, multiple files sequentially copied to SD card.

6 , stored in the SD card's effect should in turn be named: 00_1.led, 01_1.led, 02_1.led.

Notes: 1. ports with load 512/1024 lights, the playback speed of up to 30 frames / sec ports with load exceeding 512/1024 lamp, with a frame rate

       Increasing the number of lights automatically reduced.

     2. controls 32 level gray scale IC , single port control is less than 1024 when the frame rate up to 30 frames / sec. Control 256 -level grayscale IC control when a single port is less than 512 pixels at a frame rate of up to 30 frames / sec.

Second, support chips:

Support chips	LedEdit software corresponding model	Single load of lights	Remarks
LPD6803, D705,1101,6909, 6912	T-1000-6803	2048 pixels
LPD8806, LPD8809	T-1000-8806	2048 pixels
TM1803, TM1804, TM1809, TM1812	T-1000-TM	2048 pixels	TM1804 and TM1809have high and low points
TM1903 , TM1904 , TM1909 ,TM1912	T-1000-TM19	2048 pixels
UCS6909 , UCS6912 ,UCS7009 , UCS5903	T-1000-UCS-32	2048 pixels
UCS1903 , UCS1909 ,UCS1912	T-1000-UCS-256	2048 pixels	There are high-speed and low-speed points
UCS3903	T-1000-UCS-1024	2048 pixels
DMX512	T-1000-DMX	170/512pixels	Compatible with standard DMX512protocol
WS2801, WS2803	T-1000-WS	2048 pixels
WS2811	T-1000-WS2811	2048 pixels	There are high-speed and low-speed points
DS189	T-1000-DS189	2048 pixels
TLS3001, TLS3002 , TLS3008	T-1000-TLS	1024 pixels
P9813	T-1000-P9813	2048 pixels
SM16715	T-1000-SM16715	2048 pixels	There are high-speed and low-speed points
SM16716	T-1000-SM16716	2048 pixels
BS0901, BS0902	T-1000-0901	2048 pixels
BS0815	T-1000-0815	2048 pixels

Read More

No comments