C1 System Features
1,32 level -65 536-level grayscale control, software Gamma correction process.
2, supports a variety of point, line, surface light source, supports a variety of rules, shaped handle.
3, single-port controller output, the largest with 2048 pixels.
4, offline control and play content stored in the SD card.
5, C1 store up to 16 files, multiple files sequentially copied to SD card.
6, stored in the SD card's effect should in turn be named: 00_1.led, 01_1.led, 02_1.led.
7, compatible with single-wire IC, then single-IC fixtures, no need CLK clock.
Note: When 1 C1 ports with load 512 lights, the playback speed of up to 30 frames / sec ports with load more than 512 lights, frame rate with
Increasing the number of lights automatically reduced. Second,
support chips
|
Software support chips Ledctrl
|
corresponding model
|
single load lights Remarks
|
TM1803,TM1804,TM1809,TM1812
|
C1-TM
|
2048
|
There are high-speed and low-speed points
|
TM1829
|
C1-TM1829
|
2048
|
There are high-speed and low-speed points
|
UCS1903,UCS1903B ,UCS1909,UCS1912
|
C1-UCS256
|
2048
|
There are high-speed and low-speed points
|
UCS2903,UCS2909,UCS2912,
|
C1-UCS256
|
2048
|
There are high-speed and low-speed points
|
UCS6909,UCS6912,UCS7009,UCS5903
|
C1-UCS32
|
2048
|
|
WS2811
|
C1-WS2811
|
2048
|
There are high-speed and low-speed points
|
INK1003
|
C1-TM
|
2048
|
There are high-speed and low-speed points
|
TLS3100
|
C1-TM
|
2048
|
There are high-speed and low-speed points
|
SM16711
|
C1-SM16711
|
2048
|
There are high-speed and low-speed points
|
SM16716
|
C1-SM16716
|
2048
|
|
SM16726
|
C1-SM16726
|
2048
|
|
LPD6803,D705,1101
|
C1-6803
|
2048
|
|
LPD8806,LPD8809
|
C1-8806
|
2048
|
|
P9813
|
C1-P9813
|
2048
|
|
WS2801,WS2803
|
C1-WS2801
|
2048
|
|
GW6203
|
C1-TM
|
2048
|
|
Third, the appearance of the picture: Figure a Figure II Four, silk meanings:
Key meaning: Key implications Save SET to save settings (If you press the SET button, the current settings file and playback speed is saved after the next boot still press play).
Mode MODE switch file
Speed SPEED + speed while pressing SPEED + and SPEED-, then enter the file loop playback mode Slow down the speed SPEED-
TTL signal (245 signals): CLK clock line power supply indicator lamp POWER DAT data line failure ERROR LED lights GND Ground SD SD Card Slot Note:
TTL signal output for the controller and lamps must be for the land (that is, the ground and the lamp output is connected to ground controllers together).
V. wiring Note: 1, C1 is a single output port, with up to 2048 pixels;
2, when the control single-controller IC simply DAT and GND GND with lamps DAT and connected to the corresponding. When the control wire to the controller IC to be DAT.CLK and GND and lamps DAT, CLK and GND are connected to the corresponding.
3, the new project in effect when editing software, select Control Model: C1-IC Model Six, file storage:
File naming rules:
The effect of naming a single controller
"00_1.led" --------- first one results "01_1.led" --------- The first two effects
"02_1.led" --------- The first three results
"03_1.led" --------- Section 4 results Seven specific parameters:
Card:
Type: SD Card
Capacity: 128MB-2GB
Format: FAT format
Save the document:. * Led
Physical parameters:
Working temperature: -30 ℃ -85 ℃
Power supply: DC 5V input
Power consumption: 1W
Data transfer port: 3pin terminal block
Weight: 0.25Kg with packaging (3pin terminal block * 1; SD card * 1; Power Adapter * 1; Tray * 1) Size:
Note: Before you copy files to the SD card, you must format the SD card, attention is to be formatted before each copy. SD card must be formatted as "FAT" format.
Note: SD card controller can not hot-swappable, plug the SD card each time that you must first disconnect the power controller.
Eight, FAQs treatment: Question
1: After power, C1 errors found ERROR indicator has been flashing, and no effect output A: The error LED flashes ERROR been proven reader controller is not correct, there may be a problem are: ①SD card inside is empty, there is no effect file.
②SD card inside the effect file * .led files and controller models do not match, the latest version Ledctrl inside the right choice model C1- controller chip model, and re-create the effect of file * .led. ③SD card effect until a copy of the file is not formatted as FAT kinds.
④ Replace the SD card before testing, SD card bad possibilities excluded.
⑤ effect file name wrong, change 00.led.
Question 2: After the controller is powered lights normal, but no effect changes in lighting A: The reasons for this are the following:
① Check the signal lines and lighting controller is not connected properly.
② lamps and controllers must be common ground that the lamp ground and ground controllers to be tied together.
③ Please check the effect of making the SD card files * When .led selected models used are consistent with the current lighting chips.
Question 3: Connect the controller and lighting, strobe lighting, and there is the effect of the change, while the controller LEDs display properly. A:
① ground between the controller and the lighting is not connected. Effect made
②SD card inside a mistake, do not match the selected effect when the actual lighting fixtures chips and chips.
③ insufficient supply voltage lamps.
Problem 4: SD card can not be formatted. A:
① first confirm whether the side of the SD card protection switch is already unlocked. Unlocking direction SD card lilies that end.
② protection lock has been designed according to the requirements, but still can not be formatted, if that happens, most of SD card reader is broken, replace the SD card reading device.
③ If the above actions do not solve the problem of formatting, replace the SD card and re-tested.
1 ความคิดเห็น:
C1 use Program LED EDIT 2012 control ?
Post a Comment